How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
Just about every person will have their personal way of thinking with regards to How to Install a Bathtub Yourself.
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a moderately tough task. If the old tub is readily accessible, the project can move immediately; if you need to open up a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have actually currently acquired a brand-new tub and don't need to change the setup of your previous water pipelines.
Your tools as well as material checklist should consist of the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub ought to wait up until the tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The former type needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with wetness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a good friend on another site. Loved our write-up? Please share it. Let other people discover it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Appointment Report this page